LYSAGHT® Zed & Cee Purlins and Girts

Product Description and Features

LYSAGHT® Purlins and Girts are lightweight structural steel members, designed in accordance with the AS/NZS 4600: 1996 Cold Formed Steel Structures utilising high strength zinc-coated steel.

LYSAGHT® Zed sections may be used over single spans, unlapped and lapped continuous spans in multi-bay buildings. Lapped continuous spans result in considerable capacity increase in the system.

LYSAGHT® Cee sections may be used in single spans, and unlapped continuous spans in multi-bay building and are ideal as eave purlins or where compact sections are required for detailing.

  • A range of gauges and depths are available
  • Can be provided punched and unpunched
  • Non-standard sizes may be available on application
  • A down-turned bottom lip on your LYSAGHT® Zed Purlin, is available on request.
Note:
  • LYSAGHT® Cee sections cannot be lapped
  • Cee and Zed purlins are normally supplied un-punched. If punching is required punching details should be specified at the time of ordering
  • Purlins should be stored off the ground and on a slight slope so that water can drain away
  • Direct contact of incompatible material with coating should be avoided. In such applications, suitable paint systems should be obtained from paint manufacturers
  • Consider orientation of Zed and Cee purlins in relation to possible build-up of substances such as dust or grain
  • Special transport requirements are needed for lengths over 12000mm
  • Span tables assume the use of LYSAGHT® bridging and LYSAGHT® recommended bolts

Brochures

LYSAGHT® Zed & Cee Purlins and Girts User Manual Part 1

LYSAGHT® Zed & Cee Purlins and Girts User Manual Part 2

Section Properties for the South Australian Purlin - LYSAGHT® Cee Purlin C7510

LYSAGHT® Fascia Purlins

Lysaght

Important product update

Release date 1 August 2013

Following BlueScope’s launch of next generation ZINCALUME® steel, Lysaght has commenced supplying our unpainted product range using next generation ZINCALUME® steel AM125 where previously original ZINCALUME® steel AZ150 would have been used . Next generation ZINCALUME® steel AM125 is guaranteed by BlueScope to meet AS1397 and the ‘deemed to satisfy’ requirements of the Building Code of Australia for applications such as roofing and walling.

We are currently updating the Lysaght website and brochures to reflect this change. In the meantime, where the enclosed literature makes reference to ZINCALUME® the reader should note that this may refer to the previous version of the product.

Due to its increased corrosion performance compared to original ZINCALUME® steel AZ150, roofing applications made from next generation ZINCALUME® steel AM125 will be backed by an improved warranty of up to 36 years.*

*For full terms and conditions and to determine the eligibility of your project for the warranty visit www.bluescopesteel.com.au/warranties or call BlueScope on 1800 022 999

For further information on next generation ZINCALUME® steel visit http://www.nextgenzincalume.com.au.

Download Now

LYSAGHT® C100 purlin CAD file

LYSAGHT® Z100 purlin CAD file

LYSAGHT® C350 purlin CAD file

LYSAGHT® C150 purlin CAD file

LYSAGHT® Z300 purlin CAD file

LYSAGHT® C300 purlin CAD file

LYSAGHT® Z350 purlin CAD file

LYSAGHT® C200 purlin CAD file

LYSAGHT® Z200 purlin CAD file

LYSAGHT® Z250 purlin CAD file

LYSAGHT® Z150 purlin CAD file

LYSAGHT® C250 purlin CAD file

This search will find the ten closest suppliers for the location you enter, for the selected product. Fill in each of the fields below, then click "SEARCH"

Please note this locator only contains suppliers in AUSTRALIA. If you need suppliers in other countries please contact your local BlueScope Steel office.

Fields marked with * are required

Span  Tables

Limit State Capacity tables for different purlin configurations can be found in the user manual.

NOTE: New South Wales designers must refer to the New South Wales LYSAGHT SupaZed® and LYSAGHT SupaCee® Purlins and Girts Range.

Holes and Cleats

Zed and Cee sections are normally supplied with holes punched to the Australian Institute of Steel Construction (AISC) gauge lines, except in Victoria where the 150 series sections are punched to the Structural Steel Fabricators Association, Victoria, recommended gauge lines.

 

a

Specification

LYSAGHT® Zed and Cee sections are roll-formed from GALVASPAN® steel complying with AS1397 - 1993. In the grades shown, the numbers prefixed with G indicate minimum yield stress in MPa. The numbers prefixed with Z indicate minimum coating mass in g/m2.

1.0mm BMT: G550, Z350*
1.2mm BMT: G500, Z350*
1.5, 1.9, 2.4 & 3.0 mm BMT: G450, Z350*

* All BMTs in Townsville have Z450 coating.

Section Properties

Section properties for different purlin configurations can be found in the downloadable manual.

NOTE: New South Wales designers must refer to the New South Wales LYSAGHT SupaZed® and LYSAGHT SupaCee® Purlins and Girts Range.

Schematic

LYSAGHT® C Purlin LYSAGHT® Z Purlin

 

Disclaimer

Availability


NSW4 WA3 SA/NT QLD VIC/TAS
C 75- - Yes (SA Only5)- -
C/Z 100YesYesYesYesYes
C/Z 150- YesYesYesYes
C/Z 200- YesYesYesYes
C/Z 250-C 250 yes (Z2501)Yes2YesYes
C/Z 300-YesYes2Yes1Yes1
C/Z 350-YesYes2Yes1 Yes1

1 Extended lead times may apply. Contact your local service centre for availability
2 Price and availability subject to application. Extended lead times apply. Contact your nearest Lysaght service centre for availability.
3 A turn down lip is available on C/Z 150, C/Z 200, and C 250 purlins. Minimum order quantities are required.
4 For purlin availability in New South Wales, please see LYSAGHT SupaZed® and LYSAGHT SupaCee® Purlins and Girts
5 C 75 is only available in South Australia, and you can Download Section Properties for the South Australian Purlin; LYSAGHT Cee Purlin C7510 (216 KB)

Other purlin profiles may be available subject to application and will incur added charges &/or lead times.

 


Design

Span  Tables

Limit State Capacity tables for different purlin configurations can be found in the user manual.

NOTE: New South Wales designers must refer to the New South Wales LYSAGHT SupaZed® and LYSAGHT SupaCee® Purlins and Girts Range.

Holes and Cleats

Zed and Cee sections are normally supplied with holes punched to the Australian Institute of Steel Construction (AISC) gauge lines, except in Victoria where the 150 series sections are punched to the Structural Steel Fabricators Association, Victoria, recommended gauge lines.

 

a

Specification

Specification

LYSAGHT® Zed and Cee sections are roll-formed from GALVASPAN® steel complying with AS1397 - 1993. In the grades shown, the numbers prefixed with G indicate minimum yield stress in MPa. The numbers prefixed with Z indicate minimum coating mass in g/m2.

1.0mm BMT: G550, Z350*
1.2mm BMT: G500, Z350*
1.5, 1.9, 2.4 & 3.0 mm BMT: G450, Z350*

* All BMTs in Townsville have Z450 coating.

Section Properties

Section properties for different purlin configurations can be found in the downloadable manual.

NOTE: New South Wales designers must refer to the New South Wales LYSAGHT SupaZed® and LYSAGHT SupaCee® Purlins and Girts Range.

Schematic

LYSAGHT® C Purlin LYSAGHT® Z Purlin

 

Disclaimer

Availability

Availability


NSW4 WA3 SA/NT QLD VIC/TAS
C 75- - Yes (SA Only5)- -
C/Z 100YesYesYesYesYes
C/Z 150- YesYesYesYes
C/Z 200- YesYesYesYes
C/Z 250-C 250 yes (Z2501)Yes2YesYes
C/Z 300-YesYes2Yes1Yes1
C/Z 350-YesYes2Yes1 Yes1

1 Extended lead times may apply. Contact your local service centre for availability
2 Price and availability subject to application. Extended lead times apply. Contact your nearest Lysaght service centre for availability.
3 A turn down lip is available on C/Z 150, C/Z 200, and C 250 purlins. Minimum order quantities are required.
4 For purlin availability in New South Wales, please see LYSAGHT SupaZed® and LYSAGHT SupaCee® Purlins and Girts
5 C 75 is only available in South Australia, and you can Download Section Properties for the South Australian Purlin; LYSAGHT Cee Purlin C7510 (216 KB)

Other purlin profiles may be available subject to application and will incur added charges &/or lead times.

 




 
BlueScope Steel Limited
ABN 16 000 011 058
BlueScope and Lysaght
are trademarks of BlueScope Steel Limited
Australian Made Lysaght